E-11 Blaster Scope STL Files


Designed specially for my TDTroniX V1 PCB Board and electronics or can be used as a static prop.



  • Simple to Assemble.
  • Designed Specifically for SCTroniX Scope Electronics.

Please Note: Parts will require sanding to finish and make some parts fit snug.
Remember to allow room when fitting together for the thickness of the paint.



To achieve a high quality finish on the prop, these are the steps needed.

  1. Sand using 800 grit sandpaper for the first sanding.
  2. Sand using 240 grit sandpaper for the for a smoother finish.
  3. Fill any joints, seams or print lines using a good quality filler - (Optional)
  4. Sand using 240 grit sandpaper again and check for blemishes.
  5. Repeat steps 3 and 4 if necessary.
  6. Sand using 600 grit wet and dry sandpaper.
  7. Finish off with a good sand using 1200 grit wet and dry sandpaper


  1. Paint with filler primer.
  2. Check for any blemishes and fill if necessary
  3. Sand using either 600 or 1200 grit wet and dry sandpaper.
  4. Prime with a few coats.
  5. Final sand using 1200 grit wet and dry sandpaper.
  6. Finally paint in the desired colour with a few this coats.
  7. Weathering is optional.

This is a time consuming process, but the more preparation you do the better the final finish and end result.


You will receive 2 sets of STL Files:

  1. Scope STL Files to house the 0.49" OLED Display
  2. Scope  STL Files to house the 0.66" OLED Display

Please Note: The 0.66" Scope is slight larger - approximately 2mm larger in diameter around the eye piece end only


Item is a digital download of the STL files in Zipped format:

Log into your account to access your downloads. You will be able to download both versions.

1 x E-11 Blaster Scope - 0.49" OLED Display

1 x E-11 Blaster Scope - 0.66" OLED Display


Please Note: A 3D Printer is required to print these files.

Before placing your order, please make sure you are fully aware of the shipping policy outlined here: Shipping Policy

Electronics Video Demonstration:

Write a review

Please login or register to review

E-11 Blaster Scope STL

  • PropTroniX
  • Product Code: PT-0157
  • Reward Points: 37
  • Availability: 99
  • £7.50

  • Price in reward points: 750

Related Products

Red Dot Laser Diode LED

Red Dot Laser Diode LED  Important Information: Laser Safety: Looking directly ..


Blaster Scope Magnets

3D Printed Blaster Scope Magnet Set  4mm x 3mm (DxH) Neodymium Magnets - Pack of..


Micro JST 1.25mm M/F

Micro JST 1.25mm Connector Leads  A Single pair of Male & Female 1.25mm M..


0.49" OLED Display

0.49" OLED Display  This is the 0.49" OLED display module with a resolution of 64x..


6mm Tactile Switch

6mm Tactile Momentary Switches    The body of the switch measures 6mm x 6mm x ..


0.66" OLED Display

0.66" OLED Display  This is the 0.66" OLED display module with a resolution of 64x..


E-11- Scope Front Screws

E-11 Blaster Scope Front Screws  M2 Slotted Cheese Head Machine Screws for the front..


Round Glass Cabochon Lens

Round Magnifying Glass Cabochon Lens   A round crystal glass Dome shaped cabochon m..


SCTroniX DFRobot Beetle

SCTroniX DFRobot Beetle - Blaster Scope Code   A DFRobot Beetle supplied p..


1/4W Carbon Film Resistors

1/4W Carbon Film Resistors   1/4W Carbon Film Resistor 5% 0.25W   ..


40mm x 40mm Tinted Film

Tinted Film Square 40mm x 40mm  A Square piece of coloured tinted film which I use b..


Tags: E-11, Blaster, Scope, STL